KIT 1/8 ELECTRIC 4WD BUGGY MBX7R ECO MUGEN SEIKI

• Heavy duty aluminum motor mount housing A
• Heavy duty aluminum motor mount B
• Lightweight conical gears
• Straight cut conical and ring differential gears
• Specially designed front upper and rear lower suspension arms, front hub carriers, rear suspension arms and hub carriers
• Fully adjustable steering with new geometry, servo saver and ackerman plate
• Front/Rear 16mm hard anodized threaded shocks with 3.5mm shock shafts and slim rubber boots
• 3mm A7075 hard anodized chassis
• 5mm A7075 aluminum front shock tower
• 4mm A7075 aluminum rear shock tower
• 5mm A7075 aluminum lower suspension mounts for optimized geometry
• Stylish cab forward body
• Re-designed wing mount and high-down force wing

• E2129 Front Upright
• A new designed front hub carrier that incorporates the front universal to be in a trailing axle position. A new universal (E2218) is used with this hub and it uses an 8mm x 16mm ball bearing.
• E2131 Rear Upright
• The rear hub carrier has been modified to allow for use of an 8mm x 16mm ball bear which is required for the new (E2219) universal shaft. This hub carrier will also allow the use of the 15mm x 21mm ball bearing too. This hub carrier can be used for either the MBX7R or MBX7.
• E2132 Front Upper Arm
• The front upper suspension arm has been shorten 1.6mm. This will allow the use of the E0161 spacer between the pillar ball and the upper arm. This will allow for the same camber on each side of the buggy.
• E2133 Rear Lower Arm
• The suspension arm has been modified to allow for clearance so the new E2219 universal doesn’t rub the arm. This arm will work on either the MBX7R ECO or MBX7 buggy.
• E2218 Front Universal Shaft
• A new design universal drive shaft set for the front of the MBX7R ECO. The E2129 front upright must be used with these universals as they require an 8mm x 16mm ball bearing. The length of the drive shaft is 91.5mm.
• E2219 Rear Universal Shaft
• A new design universal drive shaft set for the rear of the MBX7R ECO. The E2131 rear upright must be used with these universals as they require an 8mm x 16mm ball bearing. The length of the drive shaft is 89.5mm.
• E2314 Steering Plate
• The new steering ackerman plate has 5 adjustment holes for maximum steering adjustability.
• E2408 Wing Stay
• A new wing mount that can move the wing forward maximum 10.5mm to improve traction and overall feeling of the buggy.
• E2409 Stone Guard
• The sides of the stone guard are changed to fit the new chassis.
• E2411 Chassis
• The side angle of the chassis has been changed to increase chassis strength. This will allow for a better feeling on all surfaces.
• E2528 Front 16mm Shock Set
• E2529 Rear 16mm Shock Set
• New 16mm Front/Rear shocks which will greatly improve stability in bumps and jumps

•  Front – 7,000 wt Oil (B0323)
• Center – 7,000 wt Oil (B0323)
• Rear – 3,000 wt Oil (B0321)

• Front:
• 550 wt Oil (B0333) / φ1.5 L75/7.75T Spring (E0573) / φ1.3 8H Piston (E2525) / φ2.3mm (E0164)
• Rear:
• 550 wt Oil (B0333) / φ1.5 L86/8.0T Spring (E0577) / φ1.3 8H Piston (E2525) / φ2.7mm (E0168)

Nota: Este artigo é contra-indicado para crianças com menos de 3 anos.